Getting Started - Running the USB Host - Composite

1) Before attaching the PIC24FJ256GB110 PIM to the Explorer 16 board, insure that the processor selector switch (S2) is in the “PIM” position as seen in the image below.

2) Short the J7 jumper to the “PIC24” setting

3) Before connecting the PIC24FJ256GB110 PIM to the Explorer 16 board, remove all attached cables from both boards. Connect the PIC24FJ256GB110 PIM to the Explorer 16 board. Be careful when connecting the boards to insure that no pins are bent or damaged during the process. Also insure that the PIM is not shifted in any direction and that all of the headers are properly aligned.

4) On the USB PICTail Plus board, short jumpers JP2 and JP3. Remove all other shorts on the board.

5) Connect the USB PICTail Plus board to either of the female PICTail Plus connectors or on the card edge connector (J9) at the edge of the Explorer 16 board.

Note: When using the HID bootloader for PIC32, it is important to modify the procdefs.ld file to relocate the sections of code that will hold the bootloader and those sections that will hold the user application. Example modified procdefs.ld files have been provided with each project. This file is currently named “Procdefs.ld.boot”. When using the example project with the bootloader it is required to remove the “.boot” section of the file. This will allow MPLAB to use this file instead of the default linker file. Once the linker file is renamed, however, the project will no longer work without the bootloader. Please rename the file in order to get the project working again with PIC32.

Firmware:

To run this project, you will need to load the corresponding firmware into the devices. There are two methods available for loading the demos: Precompiled demos and source code projects.

Precompiled Demos are available in the “<Install Directory>\USB – Precompiled Demos” folders. Each demo should be prefaced with the hardware platform it is compiled for. Select the file that matches the hardware that you have and the demo that you want to run. For more information about how to load a precompiled project, please see the “Getting Started – Loading a precompiled demo” guide.

The source code for this demo is available in the “<Install Directory>\USB Host - Composite - HID + MSD” directory. In this directory you will find all of the user level source and header files as well as project and workspace files for each of the hardware platforms. Find the project (*.mcp) or workspace (*.mcw) file that corresponds to the hardware platform you wish to test. Compile and program the demo code into the hardware platform. For more help on how to compile and program projects, please refer to the MPLAB® help available through the help menu of MPLAB (Help->Topics…->MPLAB IDE).

Running the Demo:

This demo supports a composite device with HID and MSD interfaces only. Please refer HID host and MSD host documentation to understand the individual host requirements. The device end can be programmed on any of the development boards for which "USB Device - Composite - HID + MSD" demo is implemented. The composite host demo works in two steps.

Step 1 - The MSD interface opens a file "test.txt" with text "This is from Composite Host." as the content of the file.

Step 2 - The HID interface gets POT value from the device and displays it on the LCD mounted on the Explorer 16 board. On press of switch 'S6' on Explorer 16 board HID interface sends a command to toggle the LED's on the device board.

Note: when bootloading this application using the HID bootloader, please make sure that the “Allow Configuration Word Programming” box is checked. This is required to be able to program the interrupt vectors on PIC24 products. As this demo requires interrupts it will not work without this feature enabled.

Limitations

Current version of the software supports the composite devices by Classes only and does not support devices by VID/PID. This Composite host demo is tested with "USB Device - Composite - HID + MSD" that is part of the same stack. The transfer events macro USB_ENABLE_TRANSFER_EVENT must be commented in file usb_config.h, these are not supported for composite host demo in current release. USB configuration utility USBConfig.exe does not support composite host in current release.

Trademarks:

The Microchip name and logo, the Microchip logo, MPLAB, and PIC are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries.

PICDEM is a trademark of Microchip Technology Incorporated in the U.S.A. and other countries.

Microsoft, Windows, and Windows Vista are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.